您好,欢迎您光临全球阀门网,发布采购

当前位置:全球阀门网 > 阀门产品 > 其它 > 其它 > 磁翻柱液位计

产地:上海

规格:UHZ

公司所在地:上海上海

电话:86-021-58212027

上海蒙泰仪表有限公司

  • 联系人:王秀红
    最新产品 | 最新供应 | 阀财通档案 | 公司介绍
  • 阀财通指数:0
    工商注册信息:未通过阀门网认证
  • 电 话:86-021-58212027 ,13564965040
    (联系时,请一定说明是从全球阀门网看到的,本网不参与交易过程,谨慎交易)
    传 真:86-021-50939827
    地 址:上海市浦东新区高科西路1862号406-408室
详细信息

磁翻柱液位计的简单介绍

磁翻柱液位计系列 UHZ系列磁翻柱液位计 ■概述INTRODUCTION UHZ系列磁翻柱液位计是公司引进国外同类产品,并加以技术改进生产的产品。系列产品可以做到高密封、防泄漏和在高温、高压、高粘度、强腐蚀性条件下安全

磁翻柱液位计的详细信息

磁翻柱液位计系列

UHZ 系列磁翻柱液位计

■概述 INTRODUCTION

UHZ系列磁翻柱液位计是公司引进国外同类产品,并加以技术改进生产的产品。系列产品可以做到高密封、防泄漏和在高温、高压、高粘度、强腐蚀性条件下安全可靠地测量液位,全过程测量无盲区,显示醒目,读数直观,且测量范围大,配上液位报警、控制开关,可实现液位或界位的上、下限报警和控制,配上 LB型液位变送器,可将液位、界位信号转换成二线制 4~20mADC标准信号,实现远距离检测、指示、记录与控制。系列产品广泛用于电力、石油、化工、冶金、环保、船舶、建筑、食品等待业生产过程中的液位测量与控制。

UHZ series magnetic reversing column liquid level gauges are designed and manufactured by MENGTAI improved on foreign similar products. The series of products have advantages such as good seal, leakage proof and reliable operation in high temperature, high pressure, high viscidity and strong corrosive situation. No blind area in whole measuring range, striking in display, clear in reading and wide in range. Matched with alarm or control switch, the level or interface can be alarm or controlled at upper or lower points. While matched with LB transmitter, the liquid level or interface can be transferred into 4~20mADC standard signal to realize measure, indication, recording or control long distance. The products are widely applied in the field of electric power, petroleum, chemical industry, metallurgy, environment protection, shipping, architecture and foodstuff.

■主要技术参数 MAIN TECHNICAL PARAMETERS

测量范围 measuring range300~15000mm

精确度 accuracy:±10mm

介质密度 specific gravity of medium:≥0.45g/cm3

介质密度差 specific gravity difference of medium for interface:≥0.15g/cm3 (测量界位)

环境振动 environment vibration:≤25Hz振幅amplitude0.5mm

跟随速度 follow rate:≤0.08m/s

介质粘度 medium viscidity:≤0.4Pa S,对于粘度大的介质或温度低时易结晶的介质,可选用加热夹套型液位计。 For bigger viscidity medium or crystalline medium at low temperature, jacket type can be used.

连接法兰 connecting flange:基本型 basic typeHG20592~20635-97 DN25 PN1.0

其它法兰标准如 GBANSIDIN等请用户注明 Other standard on request

■结构原理 STRUCTURE PRINCIPLE

液位计根据浮力原理和磁性耦合作用原理工作的。当被测容器中的液位升降时,液位计主导管中的浮子也随之升降,浮子内的永久磁钢通过磁耦合传递到现场指示器、驱动红、白翻柱翻转 180°,当液位上升时,翻柱由白色转为红色,当液位下降时,翻柱由红色转为白色,指示器的红、白界位处为容器内介质液位的实际高度,从而实现液位的指示。

The liquid level gauge operates on principle of buoyancy and magnetic coupling effect. When liquid level in measured vessel changes, the float in guide tube moves correspondingly. The permanent magnet in float actuates the reversing column to reverse 180° between red and white

due to magnetic coupling. As liquid level increases, column reverses into red from white, while liquid level decreases, column reverses into white from red. The red/white interface of indicator is level of liquid in vessel.

UHZ-801侧装式磁翻柱液位计

适用范围 SUITABLE RANGE

UHZ-801型是最常用的侧装式磁翻柱液位计,适用于工作压力低于2.5MPa,工作温度低于200℃的液体介质的液位测量。

UHZ-801 is side-mounted magnetic reversing column liquid level gauge in most common use. It is suitable to measure the level of liquid medium which operating pressure less than 2.5 MPa and operating temperature less than 200.

主要技术参数MAIN TECHNICAL PARAMETERS

测量范围 measuring range 两个法兰中心之间的距离 center-center distance 最小min. 150mm至最大max. 8000mm

工作压力 operating pressure2.5MPa

工作温度 operating temperature-20~200

介质密度 medium density0.5~2.0g/cm3

过程连接 process connecting 旁路侧面安装法兰side mounting flangeDN25 PN1.0PN1.6PN2.5

法兰标准flange standardHG20592~20635-97其它 法兰标准请用户注明Other standard on request

材质 material:旁路管bypass tube1Cr18Ni9Ti316L

浮子float:钛titanium

可选项 optional item

UHZ-802 型磁翻柱液位计

UHZ-802 MAGNETIC LIQUID LEVEL GAUGE

适用范围 SUITABLE RANGE

 UHZ-802型磁翻柱液位计适用于高温高压场合的液位测量,最高工作温度为520℃,最大工作压力为16.0MPa

UHZ-802 magnetic reversing column liquid level gauge is suitable for liquid level measurement in high temperature and high pressure situation. Its highest operating temperature is 520, and its maximum operating pressure is 16.0 MPa.

主要技术参数MAIN TECHNICAL PARAMETERS

测量范围 measuring range 两个法兰中心之间的距离 center-center distance

最小min. 150mm至最大max. 8000mm

工作压力 operating pressure16.0MPa

工作温度 operating temperature:≤520

介质密度 medium density0.45~2.0g/cm3

过程连接 process connecting:旁路侧面安装法兰side mounting flangeDN25 PN16.0凸面,

法兰标准flange standardHG20592~20635-97其它 法兰标准请用户注明Other standard on request

材质 material 旁路管bypass tube00Cr17Ni14M2(316L304) 浮子float:钛titanium

reversing column:陶瓷ceramic

可选项 optional item

UHZ-803 低温型磁翻柱液位计

UHZ-803 LOW TEMPERATURE MAGNETIC LIQUID LEVEL GAUGE

适用范围 SUITABLE RANGE

UHZ-803低温型磁翻柱液位计适用于低温场合的液位测量,最低工作温度为-196℃,最大工作压力为4.0MPa

UHZ-803 low temperature magnetic reversing column liquid level gauge is suitable for liquid level measurement in low temperature situation. Its lowest operating temperature is -196, and its maximum operating pressure is 4.0MPa.

主要技术参数MAIN TECHNICAL PARAMETERS

测量范围 measuring range 两个法兰中心之间的距离 center-center distance

最小min. 300mm至最大max. 8000mm

工作压力 operating pressure4.0MPa

工作温度 operating temperature-196~100

介质密度 medium density0.38~1.2g/cm3

过程连接 process connecting:旁路侧面安装法兰side mounting flangeDN25 PN4.0

法兰标准flange standardHG20592~20635-97其它 法兰标准请用户注明Other standard on request

材质 material 旁路管bypass tube00Cr17Ni14M2(316L) 浮子float:钛titanium

可选项 optional item

UHZ-804 石油液化气专用型磁翻柱液位计(侧装式)

UHZ-804 MAGNETIC LIQUID LEVEL GAUGE FOR PETROLEUM LIQUEFIED GAS

适用范围 SUITABLE RANGE

该产品适用于易汽化的液体测量,尤其适合液化气介质的液位测量;其特点是用挡杆将液位计主导管内腔分成气化室和测量室,当液位计内液化气受温度影响, 内部汽化而产生气泡时,气泡会顺着气化室往上冒,而不会进入测量室影响磁浮子工作,有效地阻止了因气泡

造成磁浮子跳动,使液位计在液体介质大量气化时,也能可靠地工作。

The products are applied to measure the level of vaporizable liquid especially liquefied gas. Blocking lever is used to divide guide tube into gasification chamber and measure chamber. When liquefied gas is infected by temperature and vaporize into being gas bubbles, the bubbles will rush up along gasification chamber and not enter into measure chamber to affect magnetic float. Which effectually prevents magnetic float jumping. So the gauge can operate reliably even at liquid medium vaporizing a lot.

主要技术参数MAIN TECHNICAL PARAMETERS

测量范围 measuring range 两个法兰中心之间的距离 center-center distance 最小min. 150mm至最大max. 8000mm(14000mm)

工作压力 operating pressure2.5MPa; 4.0MPa

工作温度 operating temperature-20~100

介质密度 medium density0.4~1.2g/cm3

过程连接 process connecting:旁路侧面安装法兰side mounting flangeDN25 PN2.5,或PN4.0凸面

法兰标准flange standardHG20592~20635-97其它 法兰标准请用户注明Other standard on request

材质 material 旁路管bypass tube30400Cr17Ni14M2(316L) 浮子float:钛titanium

可选项 optional item

UHZ-805 无盲区耐腐型磁翻柱液位计

UHZ-805 NO BLIND AREA AND CORROSION-PROFF MAGNETIC LIQUID LEVEL GAUGE

适用范围 SUITABLE RANGE

UHZ-805无盲区耐腐型磁翻柱液位计适用于腐蚀性介质且工作温度又较高场合的液位测量,由于采用先进的不锈钢内衬聚四氟乙烯拉伸翻边新工艺,使液位计测量无盲区,结构可靠,使用寿命长。

UHZ-805 no blind area and corrosion-proof magnetic liquid level gauge is suitable for corrosive medium even at higher operating temperature. Reliable in structure, long in operating life, and no blind area exists in measurement as a result of the new technics that PTFE lining is stretched across caliber of guide tube.

主要技术参数MAIN TECHNICAL PARAMETERS

测量范围 measuring range 两个法兰中心之间的距离 center-center distance 最小min. 150mm至最大max. 8000mm

工作压力 operating pressure2.5MPa

工作温度 operating temperature-30~200

介质密度 medium density0.5~2.0g/cm3

过程连接 process connecting:旁路侧面安装法兰side mounting flangeDN25 PN1.0,或PN1.6PN2.5凸面,

法兰标准flange standardHG20592~20635-97其它 法兰标准请用户注明Other standard on request

材质 material 旁路管bypass tube1Cr18Ni9Ti内衬PTFE 浮子floatPTFE

可选项 optional item

UHZ-806 耐腐型磁翻柱液位计

UHZ-806 CORROSION-PROFF MAGNETIC LIQUID LEVEL GAUGE

适用范围 SUITABLE RANGE

UHZ-806型耐腐型磁翻柱液位计采用不锈钢本体内衬聚丙烯(PP)工艺,有很高的结构强度和耐腐蚀性,可适用于盐酸等酸性、碱性液体和许多有机溶剂(尤其是活性族溶剂)。但不适用于浓缩硝酸、铬酸混合物、含氯溶剂、脂肪族、芳香氢等介质液体的测量。

UHZ-806 corrosion-proof magnetic liquid level gauge is constructed with stainless steel body with PP lining, which is high rugged and corrosion-proof. So it is suitable for acidic solution such as hydrochloric acid as well as alkaline and many organic solutions especially active solution. But on the other hand, it cannot be used for concentrated nitric acid, chrome acid mixture, chloric solution, aliphatic solution and balmy hydrogen etc..

主要技术参数MAIN TECHNICAL PARAMETERS

测量范围 measuring range 两个法兰中心之间的距离 center-center distance

最小min. 150mm至最大max. 8000mm

工作压力 operating pressure0.6MPa

工作温度 operating temperature-20~80

介质密度 medium density0.6~2.0g/cm3

过程连接 process connecting:旁路侧面安装法兰side mounting flangeDN25 PN1.0凸面,

法兰标准flange standardHG20592~20635-97其它 法兰标准请用户注明Other standard on request

材质 material 旁路管bypass tubePP 浮子floatPP

可选项 optional item

UHZ-701UHZ-702 型磁翻柱液位计

UHZ-701 AND 702 MAGNETIC LIQUID LEVEL GAUGE

适用范围 SUITABLE RANGE

UHZ-701702顶装式磁翻柱液位计主要用于各种地下储罐及侧面不宜开口的容器的液位测量。由于结构上的原因,液位计在测量时存在一定的盲区值N,对于不同介质密度,盲区值也不一样。本厂仪表出厂时,标尺刻度零位已迁移到实际值。

UHZ-701 and 702 top-mounted magnetic liquid level gauges are mainly used to measure the level in underground storage tanks and vessels that cannot be opened at side. Some blind area N must exists at measurement due to structure. And for different specific gravity medium, the blind area is different. The product leaves factory with actual value on scale at start.

主要技术参数

MAIN TECHNICAL PARAMETERS

测量范围 measuring range:最大max. 4000mm

工作压力 operating pressure2.5MPa

工作温度 operating temperature-20~200

介质密度 medium density701型:0.65~2.0g/cm3

702型:0.5~2.0g/cm3

过程连接 process connecting 701型:DN100PN1.0PN2.5凸面convex flange

702型:DN150PN1.0PN2.5凸面convex flange

法兰标准flange standardHG20592~20635-97其它 法兰标准请用户注明Other standard on request

材质 material:顶导管top guide tube304316L 浮子float:钛titanium

可选项 optional item

UHZ-703UHZ-704 防腐型磁翻柱液位计

UHZ-703 AND 704 CORROSION-PROFF MAGNETIC LIQUID LEVEL GAUGE

适用范围 SUITABLE RANGE

UHZ-703704顶装式防腐型磁翻柱液位计主要用于各种地下储罐及侧面不宜开口的容器,且有腐蚀性介质的液位测量。由于结构上的原因,液位计在测量时存在一定的盲区值N,对于不同介质的密度,盲区值也不一样。本厂仪表出厂时,标尺刻度零位已迁移到实际值。

UHZ-703 and 704 top-mounted magnetic liquid level gauges are mainly used to measure the level in underground storage tanks and vessels that cannot be opened at side. Some blind area N must exists at measurement due

to structure. And for different specific gravity medium, the blind area is different. The product leaves

factory with actual value on scale at start.

UHZ-705 石油液化气专用型磁翻柱液位计(埋地罐专用)

UHZ-705 MAGNETIC LIQUID LEVEL GAUGE FOR PETROLEUM LIQUEFIED GAS(SPECIAL FOR UNDERGROUND TANK)

适用范围 SUITABLE RANGE

该产品适用于压力容器中易汽化介质的液体测量, 尤其适合埋地罐液化气介质的液位测量。可现场显示, 输出二线制4~20mA电流信号,也可附加高低液位防爆报警开关。由于测量浮子采用三组纯钛浮球组合和独特的导轨形式,产品性能稳定可靠,实用性强,目前在

LPG加气站广泛使用。

The product is suitable for level measurement of vaporizable liquid in pressure vessels especially liquefied gas in underground tank. The level can be indicated locally, furthermore, two-wire 4~20mA transmission output and high/low switches can be optional. The float assembly

is combined with three titanium floats and moves along with unique guide rail, which makes it stable and reliable in operation. With strong practicability, the products are already applied in wide LPG gas station at present.

主要技术参数MAIN TECHNICAL PARAMETERS

测量范围 measuring range:最大max. 3000mm

工作压力 operating pressure2.5MPa4.0MPa

工作温度 operating temperature-20~100

介质密度 medium density0.4~1.2g/cm3

过程连接 process connecting DN150PN2.5PN4.0凸面,

法兰标准flange standardHG20592~20635-97其它 法兰标准请用户注明Other standard on request

材质 material:顶管:30400Cr17Ni14M2(316) 浮子float:钛titanium

可选项 optional item

我要询价

商铺首页 - 公司介绍 - 产品展示 - 供应信息 - 产品报价 - 企业新闻 - 成功案例 - 人才招聘 - 联系我们 -

联系人:王秀红 联系电话:86-021-58212027 传真:86-021-50939827 地址:上海市浦东新区高科西路1862号406-408室